Questions and answers

Of course, not only the safety of the product, but its service life depends on proper operation. The way to increase the “life expectancy” of aeromena is to take care of it properly: keep it safe, periodically check its integrity, and if any damage is detected, repair it in time, keep the casing clean - from time to time wiping up the product.

The figure is operated at a temperature of -25 ... +35 ° C, with a wind speed of no more than 7 m / s. When accelerating air masses, on a scale higher than 7 points - it is necessary to stop the work of the product, roll the casing and remove it.

Aeromenic material with water-repellent properties is not recommended to leave under prolonged precipitation. Since, with prolonged exposure to moisture, the printing of aeromen (drawings, logo, inscriptions, etc.) fades, the fabric loses its original properties, the strength of the seams is lost.

Запрещено передвигать и перемещать пневмоконструкции в надутом / в развернутом состоянии за петли и крепежные элементы. Используйте петли только для крепления пневмоконструкции на поверхности.

Перемещать пневмоконструкции допускается только в сдутом состоянии, единым модулем в свернутом виде (запрещено тащить войлоком, поднимать от земли). Перед монтажом ознакомьтесь с техническим паспортом!

Products of our company regularly undergo voluntary and mandatory tests for compliance with state standards. For example, inflatable slides and inflatable trampolines are declared according to the mandatory standard 53489, and team rides, advertising structures and peytbolnye figures, soft modules and scenes, confirmed by compliance with voluntary certification GOST R.

We provide our customers with:

• contract with specification of commodity items,
• score,
• individual products are accompanied by the development of sketches and 3d models,
• certified copy of the declaration of conformity, voluntary certificate of conformity GOST R.

Working with us, you get a complete set of all necessary documents for organizing and conducting commercial activities in the field of entertainment.

We work with transport companies: "Baikal Service", "Business Lines", "Express-Auto", "Energy", "ZhelDorEkspeditsiya" and others. A wide network of cooperation allows you to select the TC you are used to. In addition, in situations where the deadlines are on or if delivery is required at minimum rates, we will select the most convenient option for you from the existing list of companies.

Delivery is carried out in Russia, in the CIS countries and Europe.

Attention! Delivery to the terminal of the transport company in Yekaterinburg and to the terminal of the city of Moscow is free of charge!

Depending on the method of transportation, the number of days of transportation and its cost are calculated. Detailed information you can find out from the company's employees or preview the deadlines in the text below ...

The following delivery methods are available to you:

• Motor transport, general cargo and individual delivery - from 3 days.

• Air delivery - from 1 day

• Railway transport - from 3 days

• Delivery in the CIS and European countries - depend on the method of movement of cargo.

I liked the inflatable product in the picture on the Internet, but for some reason you can not buy at the addressee? No problem! You can always contact our specialists with a sketch or a photo you like. Our designers will outline all the contours of the figure you like, while technologists and sewing craftsmen will prepare patterns and make the product.

When forming the price for an inflatable attraction, it is first of all important for us that it conforms to the national standard. Therefore, the purchased material, threads, accessories not only meet the established requirements of GOST-53487, but also exceed its technical characteristics.

In addition, the cost includes the payment of personnel, laid the complexity of manufacturing the product, the cost of printing, the cost of decorating an inflatable platform. In the new product, which is not developed, laid the costs of creating patterns and the work of designers. Simply put, it consists of the cost of materials, pay for staff and a small margin.

Upon completion of the manufacture of the product, a photo report of the finished product is provided, as a rule, made from several angles: the general plan, photos from several sides and photographs of individual elements.

We are always open for the most active, enterprising, willing to open new horizons in business. And it doesn’t matter whether you start your own business from scratch or you already have a successful project.

What do we offer?

A successful product that is in constant demand in the Russian market. Inflatable figures, children's trampolines, obstacle lanes - and this is not the whole list of products, due to which you can build a full-fledged, profitable business or significantly expand the range, with benefits for the development of your company.

Unlike many companies that regulate the sales of their partners, we do not have this item in the contract. You can purchase our products, anytime, anywhere, without any sanctions and consequences for your business! In addition, cooperating with us, other useful “buns” are waiting for you: providing mock-ups and photographic materials, consulting on organizing advertising campaigns, free delivery to the terminal of your city (as agreed, depending on distance), and much more.

Read more and leave a request here .

Place the fans of the product opposite each other, after clearing the ground from debris, piercing and cutting objects. Take the figure out of the case, unfold it, hold the aerofoil in your hands so as not to stain the fabric.

Inspect the product: the shell should not be twisted. Next - tie the straps on the legs of aeromen (or fasten to the linden) to the air pumps.

Turn on the plug 220V. Wait for the figure to take a predetermined shape, after which, visually make sure that aeromen performs synchronous movements.

If there are mainly movements in one direction, then examine the position in which the fans are located - the pumps should stand exactly. Installation of the figure should be carried out at wind speeds up to 5 m / s., In the absence of prolonged precipitation.

Attention! If aeromen "froze" in one position, then adjust the flow of exhaust air using lacing on the head of the product.

Inspect the ground; it should be level without any inclinations or obstacles. Estimate the distance to the lighting and heating elements, it should be not less than 3 meters, and not less than 1 meter to any structures.

Spread the casing on the surface of previously cleaned from piercing-cutting objects. Put the sleeve on the air pump, then tie the loop on the "neck" of the fan. Make sure that there are no things near the air intake box that could damage the air pump.

Install a hangar / tent, with a wind speed of no more than 7 m / s (operation is allowed with wind force up to 15 m / s - for hangars and up to 12 m / s - for tents). After completing the above steps, turn on the fan in the network. When inflating, straighten the folds of the shell so that the air penetrates the product cylinders faster. This method will help to take pneumo structure faster given shape.

Pneumatic frame took shape, it must be fixed on the surface. Fixation is carried out in two ways: by weighting and fastening loops dispersed around the structure perimeter. The ballast is laid out in the compartments of the hangar / tent cylinders, and the attachment to the loops is done by connecting the cord to the pegs immersed in the soil.

Operation of the product is allowed at a temperature of +40 to -40 ° C.

In a static state, the fabric can easily withstand from +40 to -40 ° C, but still, at a negative temperature close to the allowable, we do not recommend repeatedly crushing the shell without an urgent need. In the cold, microcracks can form, which after a certain time, lead to damage to the appearance of the fabric, in consequence, and reduce the service life of the hangar / tent.

Inspect the ground; it should be level without any inclinations or obstacles. Estimate the distance to the lighting and heating elements, it should be not less than 3 meters, and not less than 1 meter to any structures.

Spread the casing on the surface of previously cleaned from piercing-cutting objects. Put the sleeve on the air pump, then tie the loop on the "neck" of the fan. Make sure that there are no things near the air intake box that could damage the air pump.

Set the scene when the wind speed is not more than 7 m / s (operation is allowed with a force of up to 12 m / s). After completing the above steps, turn on the fan in the network. When inflating, straighten the folds of the shell so that the air penetrates the product cylinders faster. This method will help to take pneumo structure faster given shape.

Pneumatic frame took shape, then it must be fixed on the surface. Fixation is carried out in two ways: by weighting and fastening loops dispersed around the structure perimeter. The ballast is laid out in the compartments of the scene cylinders, and the attachment to the loops is carried out by connecting the cord to the pegs immersed in the soil.

Each product is completed with the instruction manual, which contains requirements for installation, operation, compliance with safety measures and method of careful storage.

For the installation of products do not require special knowledge and tools. Products are installed in accordance with the attached instructions.

We pay special attention of our customers to the individuality of each product, the features of which are reflected in the contract, application and other documents attached to the product (technical data sheet or instruction). The Manufacturer shall not be liable for the independent actions or omissions of the Buyer in relation to the product and its use, in conditions other than those described in the contract and other documents accompanying the fulfillment of obligations, including warranty. For any questions of operation, you can contact our expert for clarification.

The material used in the manufacture of inflatable trampolines and obstacle bands, is almost twice as much as the gap values ​​indicated in GOST. Thus, the standard spelled out 1850 and 175 newtons, which the fabric should withstand for “tearing apart” - our material indicators are 3235 and 392 newtons, which, of course, makes the product more durable and resistant to stress in the long term.

Moreover, the fabric is neutral to chemical exposure - soap solution and other active substances; impregnated with polyurethane - a dirt-and water-repellent base, which, of course, expands the possibilities of operation of the attraction. Used PVC, corresponds to the density indicators GOST, and is a coefficient not lower than 650 g / m2.

When developing an individual layout for your technical task, the work of the designer is paid separately, in the amount of 3,500 rubles (cost agreed separately). If later, the sample is approved by you, and the figure will be made by us, then the payment made will be credited to the established cost of the figure. In other words, when you pay for an individual product - you get a 3d sketch for free.

Due to the fact that the winter rides belong to the line of inflatable products, therefore, before using them, the shell must be pumped. This can be done with a mechanical, foot or electric pump.

Deploy the attraction on the cleaned surface. If it is a tubing, then insert the camera into the case so that there is no free space. When inflating, make sure that the camera is evenly opened inside the shell. In the process, also check the air pressure of the attraction by pressing on it with your hand. If the product is not fully deformed under pressure, then the sledge is ready for use.

Remember, the product should not be pumped or under rolled. First, it can lead to rupture of the camera, and, secondly, it is traumatic when riding on a surface with natural obstacles.

Do not forget to control the product in case it is cold in the cold - if you do not lower the air from the chamber, bringing the sleigh into a warm room, the shell may burst.

After your first request, our manager will contact you to clarify the details of the order, tell you about the time of manufacture, agree on the dimensions of the product, color, material, etc. After that, the agreed details are written in the contract annex, and the document is mutually signed. We send its scanned copy to your email (or via whatsApp, viber) for final approval.

According to the agreed proportions of payment - you pay for the product. In turn, after the receipt of funds on the account or the provision of a payment order - from our side, a 3D model of the product is developed and agreed upon. Upon its completion, the electronic model is given for production.

Work with documents is made by three methods. Sending documents in place with the finished product to your address, which is somewhat longer than sending by Russian Post or courier service. The last two methods of shipment is carried out in the case when it is impossible to pay for the product without the originals or at your request, but with the agreement of our manager.

Winter rides (tubing and bananas) are difficult to control entertainment. Therefore, before using them for direct purpose, it is necessary to think about a safe descent from a hill. In particular, inspect the slope and think about a suitable trajectory of the route. For example, there should be no piercing and cutting objects, stones and springboards, trees and shrubs that could lead to a collision or injury.

In addition, due to the fact that winter rides develop a decent speed, it is not recommended to “go all over” from steep, uncontrollable slopes. During the start on the way there should be no strangers parallel riding with you or completing the descent, but at an unsafe distance. Thus, in order to avoid causing harm to vacationers, themselves and their loved ones, it is necessary to observe a strict sequence on the launch pad.

In our production, we use synthetic PVC fabrics, Oxford, TPU, Duspo, etc. All these types of polymers have water-repellent properties, but products made from them are not completely airtight. Moisture can penetrate the stitching segments of the segments, but under the long-term effects of precipitation in the form of rain, getting wet material is not excluded!

The general rules for structures made of PVC, Oxford, TPU, Duspo set mandatory storage requirements. Before storing the attraction, it is necessary to get rid of the remnants of moisture, pre-drying the product. Storage should be carried out in a moderately humid, ventilated room, at a temperature of from 0 to + 35 ° C.

If for some reason, the pneumo construction has lain (which we categorically, as a manufacturer do not recommend) in a cold room, then the product must be given time to “move away from winter” . To do this, place the attraction, for a while, in a warm environment.

Violations of storage conditions can lead to darkening, destruction of the structure of the material, the appearance of a fungus (mold), cracks in the print on the pictures. Especially often - this occurs in cases when the product was lying in a damp, cold room or, due to negligence, when moisture from the attraction shell was not completely removed, before placing it in a warehouse.

For questions regarding the storage, transportation of the product and the operating conditions, you can familiarize yourself in the form: question-answer in the product card of your interest, or contact our manager. We will surely help in the solution of emerging issues.

In our assortment there are inflatable trampolines of both large, medium and very small sizes, which are perfect for filling the space in the game room, children's room at home and cottage. In addition, virtually any inflatable center based on your wishes, we can make to order.

Filling a small trampoline, usually no less bright than on large rides: small slides and obstacles, three-dimensional figures and other elements - in general, everything that kids love so much.

By the way, a small trampoline is a great opportunity to diversify a children's playroom, adding an attraction as an additional, but profitable entertainment equipment.

We always have a choice of fabric, presented in more than 60 shades. You can always choose a combination of colors for your product on our website. In addition, our managers will help determine the choice, choosing the optimal combination of colors for your composition.

Attention! Reflected colors on the screen of your gadget / computer may differ slightly from the colors realized in the final product. This is due to both the color settings on your screen (color saturation), and the functions of expanding brightness, contrast and the predominant effects: blue, red screen, etc.

The product should be washed in warm water, at a temperature up to 30 ° C. As a cleaning agent, it is necessary to use a powder designed for sportswear and membrane fabric. Bleaching, spinning the casing, tumble drying and ironing are prohibited! To preserve the quality of printing and the water-repellent properties of the material, it is prohibited to rub and twist the fabric during washing.

In addition, after cleaning the shell, ironing is not recommended!

To transport the product, regardless of the category of transport, should be in a production case, at a temperature of from +40 to -40 ° C.

To transport the product, regardless of the category of transport, should be in the production case, at a temperature of from -25 to + 35 ° C.

You can leave a request on our website or call the multichannel phone number 8 800 555-62-41. Also for you phone is available for the regions +7 (996) 174-39-79. If for some reason you can not contact the specified contacts, you can always order a "callback".

You can leave a request to our managers - by emailing info@airmir.ru or via the application: WhatsApp, Skype, Viber at +7 (996) 174-39-79 . As a rule, the processing of an application in our company takes no more than 25 minutes (during working hours).

The following payment methods are available to you:
1. Cashless payments are available for all customers, legal entities and individuals.
2. Transfer through Sberbank online or other online banks.
3. Available loans in the "Federal Bank".
4. Cash payment.

Attention! Payment terms are individual, check with your personal manager for payment and terms.

Comfortable temperature range for storage from 0 to + 35 ° C. In addition, in order to avoid mold and fungi, it is forbidden to store the product without first drying it! To remove residual moisture, inflate the product for several hours indoors or outdoors in dry weather.

Comfortable temperature range for storage from 0 to + 35 ° C. In addition, in order to avoid mold and fungi, it is forbidden to store the product without first drying it! To remove residual moisture - inflate the product for several hours.

Store products during breaks in operation, it is necessary in a dry and clean place, preferably with a microclimate close to room conditions.

In the segment of inflatable products - economy figures (standard) break stereotypes that, for example, low-end models are necessarily of poor quality. In our case, the statement is not true.

What's the secret?

Sewing technology makes it possible to complicate or simplify the final result, giving the figure a more detailed look at the expense of three-dimensional elements, or vice versa to make simple contours that simplify the design model. Accordingly, more materials are spent on products of complex execution, and work on their creation takes a long time. For this reason, cost is changing, but not performance.

All products are made of the same material, common components are used, so the quality of any inflatable product remains consistently high. The service life for economy, standard and premium performance is the same.

Budget products or economy class figures are figures that are distinguished by external simplicity. Their shape is not complicated by multiple three-dimensional elements, application and ornament. Honestly, this is not necessary. For example, simple in our understanding are the figures, like an inflatable bottle, a can, a pack and a barrel. Given that the finished product can be copyright, individual, in a beautiful bright performance.

Figures of the class standard - are distinguished by more detailed details and the presence of volumetric elements. For their creation, labor costs are higher, and there are more consumable materials. Visually, the standard - the figures look fabulous, their image is well developed. For example, inflatable Santa Claus in this segment is a fabulous grandfather in a bright performance.

Premium class figures - have the highest degree of detail, in other words, the image is almost completely created by three-dimensional embroidery elements, ornament is often used, and the product according to the chosen theme is covered with printing in high resolution. Premium is an incredibly realistic figure, it does not matter if it’s a fabulous character, a copy of your product, animal figures or cartoon heroes.

Oxford is quite practical and lightweight material used in many areas of human activity. He equally well proved for operation both in the summer, and in the winter. In a static state, the fabric can easily withstand -25 to + 35 ° C, but, nevertheless, at a negative temperature close to the allowable, we do not recommend repeatedly crushing the shell without an urgent need. In severe frost, microcracks can form, which after a certain time, lead to damage to the appearance of the fabric, and, consequently, to reduce the life of the scene.

When the wind rises to the maximum permissible values, it is necessary to immediately stop using the product. Bleed the air from the structure and fold the shell. It is allowed to use pneumatic equipment at wind speed not higher than 12 m / s.